Modules & Add-ons

Pre-announcement chime generator board

The A 1708 accessory board makes it possible to transmit a signal to precede microphone announcements (chime). A single multi-pin connector makes the board easy to install. The output level can be adjusted by means of a trimmer. Using special jumpers, it is possible to choose between a single-tone, two tone or three-tone signal. Two trimmers are used for adjusting the transmission level and the frequency-decline of the signal (indirectly the tone duration).


Related products:

The AN-001T is a plug-in module of 2-channel ambient noise detector designed for use with the M-9000.
It automatically adjusts the output volume in response to the change of ambient noise level. The AN-001T can handle input signals from microphone level (-60dB) to line level (-10dB) by controlling the gain in 9 steps. Phantom power (+24V) can be supplied for condenser microphone use.

Link to manufacturer information

Related products:

Ambient Noise Sensing Microphone for M-9000
The AN-9001 is an electret condenser microphone designed for ambient
noise sensing. It is used in conjunction with the AN-001T Ambient Noise control module in the M-9000. It can be mounted in an American Standard 1-gang electrical box in the ceiling or wall.

Link to manufacturer information

Related products:

Input/Output Control Module

The C-001T is Control I/O expansion module designed for use with the M-9000 and can provide up to 8 channels each of input and output expansion. Since the main unit has 4 preinstalled inputs and outputs each, the control input and output can be expanded to up to 12 channels each when the C-001T is used.

Link to manufacturer information

Related products:

The D-001T is a plug-in module designed for use with the M-9000 and can provide two independent balanced inputs. The D-001T can handle signals ranging from microphone level to line level by controlling their input sensitivity in 9 increments from -60dB to -10dB. Phantom power (+24V) can be supplied for condenser microphone use. The D-001T can process effect for TONE/EQ/COMPRESSOR to two inputs independently.
Link to manufacturer information

Related products:

MP6003 is a 3 channels modular mixer to use in the RCF FLEXA system. Maximum useable 9 modules for 27 total inputs.

- Fast, noise free, selectable voice microphone activation with automatically adjust threshold changing background room noise.
- Selectable max number of open microphones (NOM).
- Automatic gain adjustment following activate microphone number (NOM).
- Selectable hold time.
- Master input programmable priority.
- Infinite or 15 dB channel attenuation.
- Automatic input volume control.
- Remote output volume control.
- Tone control.
- Insertion, signal and peak indicator on bicolour Led.
- Phantom power 24V selectable.
- Possibility for input activation and feedback from and towards an external system

Link to manufacturer information

24V Adapter

- 24VDC adapter module (1 FLEXA slots).
- Dedicated to be interfaced with FLEXA power supply units PS 6320 or PS 6640.
- Allows 24VDC back-up operation according to BS 5839-8 and EN 60849.
- Full Battery Charging facility.
- Full Battery Diagnosis System.
- Connector for diagnostics interface.

Link to manufacturer information

Modular auxiliary power supply unit 60W

- Power supply capacity 60W, high efficiency, for pre-amplification modules (one Flexa slot)
- Mains power supply 115/230V 50/60 Hz
- Absorbed power 90 W max.
- Battery power supply 24V
- Absorbed current 4 A max.
- Built-in protection circuits
- Automatic switching to battery with mains failure
- LED indicators for activity, DC power supply, and battery operation
- Local and remote indication of switch-on and battery connection
- Master switch on the rear panel
- Connector for diagnostic interface

Link to manufacturer information

320W Modular power supply unit.

Uses 2 Flexa Slot

Link to manufacturer information

640W Modular power supply unit.

Uses 3 Flexa Slot

Link to manufacturer information

RK-8VX

Relay Board

Relay board for sub zones.

Link to manufacturer information

Remote Microphone Extension

The Extension unit allows additional 10 zones (per unit) to be added to the RM-200 range of mics.

For use with the VM and VX range of RM Microphones

Link to manufacturer information

Related products:

Nonpolar 2-wire system I/O board for transmitting 32 each of control inputs and outputs between remotely installed boards.
For creating custom-made remote microphones.
One RN-032 can control 20 group selection keys and busy indicators.
Power source of 24V DC and operating) range of 16-33VDC.

Link to manufacturer information

Amplifier Control Unit for PM-660D

Amplifier control unit for 5 pin DIN plug remote switch type paging microphone (PM-660D).
Desktop or wall (standard bracket) mounting.
Outputs remote control signals for main amplifier power ON / OFF, and for initiating all-call paging.
Microphone volume control and talk ON indicator.
Power supplied by locally avalailable AC adaptor.

Link to manufacturer information

Related products:

Amplifier Control Unit for PM-660D with Signal

Amplifier control unit for 5 pin DIN plug remote switch type paging microphone (PM-660D).
Desktop or wall (standard bracket) mounting.
Outputs remote control signals for main amplifier power ON / OFF, and for initiating all-call paging.
Microphone volume control and talk ON indicator.
Activates selectable 4-tone, 2-tone and single tone chimes, plus gong, when paging remote microphone's talk switch is pressed.
Power supplied by locally avalailable AC adaptor.

Link to manufacturer information

Related products:

Speaker Selector

The SS-9001 is a speaker selector used with the ZP-001T zone paging module. It outputs 2 input signals to 4 different zones.

Link to manufacturer information

Related products:

Surveillance Board

For installation in the VM-2000 system management amplifier's card receptacle. The surveillance board SV-200MA provides monitoring of five speaker lines on short circuit, break and earth leakage. It also monitors the power amplifier on proper operation.
Link to manufacturer information

The T-001T is a plug-in module designed for use with the M-9000 and provide two independent balanced outputs. It can drive load of 600O up to +16dB. It can process effect for TONE/EQ/ COMPRESSOR to two inputs independently.

Link to manufacturer information

Related products:

80W Modular power amplifier unit.

Uses 1 Flexa Slot

Link to manufacturer information

240W Modular power amplifier unit.

Uses 2 Flexa Slot

Link to manufacturer information

480W Modular power amplifier unit.

Uses 3 Flexa Slot

Link to manufacturer information

V-1014B Alarm Signal Module

Siren, yelp and buzzer signals available.
Red signal LED and green paging ready LED.
Semi-fixed output level control and sounding time.

Link to manufacturer information

V-1015B Chime Module

Switchable 2-tone chime or single gong tone.
Red signal LED and Green paging ready LED.

Link to manufacturer information

V-1051B Mic Input Module with Programming Function

Compressor (switchable) is provided with Mic level input.
Various applications possible, depending on the selection of programming functions and the insertion location in the mixer frame or mixer power amplifiers.
Electrically balanced input.

Link to manufacturer information

V-1054B Auxiliary Input Module

Semi-fixed volume control for adjusting the output level during normal and priority muting operations.
Electrically balanced output

Link to manufacturer information

V-1061B Program Selector Module

4 selector buttons and 1 reset button for easy handling.
Program selectable from 4 inputs.
Balanced and unbalanced outputs provided.
Muting function available on unbalanced output line.

Link to manufacturer information

V-1062B 5-Zone Selector Module

2-in / 5-out zone selector remotely controlled from a microphone.
An override function for emergency paging.
Green and red LEDs indicate the zone selection status.
Link to manufacturer information

V-1069B Data Receiver Module

Data Receiver Module for use with VR-1010 and VR-1020 remote microphones.
Max. 20 outpu controls plus all call.
In-use / malfunction remote microphone lamp and unit error lamp.
Chime volume control and chime activation switch for internal chime OFF / ON.
Program switch (DIP switch 2) enables mics 1 ~ 4 and sets priorities (1st-in-1st-out / Selectable / No priority).
Pre-anouncement tone selection jumpers for 2-tone chime, gong or 1-tone chime.
Ground jumper may be cut to separate signal ground from chassis ground.

Link to manufacturer information

V-1071B Line Amplifier Module

Combines preamp signals with no mixing loss.
Bass and treble tone controls.
LED output level indication.
Slide volume control.

Link to manufacturer information

V-1072B Line Amplifier Module

Combines preamp signals with no mixing loss.
Bass and treble tone controls.
LED output level indication.
Semi-fixed volume control.

Link to manufacturer information

V-1082B Power Supply Module

Plug-in connection with the V-1000B mixer frame.
Supplies 24V DC power to modules in the V-1000B.
Protection circuitry for preventing shot circuits.

Link to manufacturer information

V-1251B Mic Input Module with Transformer, Isolate

Transformer isolated low impedance input.
Phantom power (switchable).
Various applications possible depending on the selection of programming functions and the insertion location in the mixer frame or mixer power

Link to manufacturer information

V-1254B Line Input Module

Transformer isolated balanced line input.
Unbalanced line output.
Front panel handle for easy removal.
Link to manufacturer information

VP-200VX Power Amplifier Input Module

The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with theVP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.

Link to manufacturer information

VP-200VX Power Amplifier Input Module with BGM Faclilty

The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with theVP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.

Link to manufacturer information

VX-200SE Equaliser Card

The VX-200SE Equaliser is a 9-band, 1-channel equaliser to be mounted on the circuit board of the VX-200SP Pilot Tone Detection module or VX-200SZ Impedance Detection module.
Link to manufacturer information

VX-200SI Control Input Module

TOA's VX-200SI Control Input Module is used to increase the number of control inputs to be used in the VX-2000 system. It features 16 control inputs and is mounted in the VX-2000SF Surveillance Frame.

Link to manufacturer information

VX-200SO Control Output Module

TOA's VX-200SO Control Output Module is used to increase the number of control outputs to be used in the VX-2000 system. It features 16 control outputs and is mounted in the VX-2000SF Surveillance Frame.

Link to manufacturer information

VX-200SP Pilot Tone Detection Module

The VX-200SP is an audio signal output module of the VX-2000 system with speaker line pilot tone detection. This module is to be mounted in the VX-2000SF Surveillance Frame and detects speaker line short circuits, open circuits by monitoring for the presence of a pilot signal, and ground fault.

Link to manufacturer information

VX-200SP-2 Pilot Tone Detection Module

The VX-200SP-2 is an audio signal output module of the
VX-2000 system with speaker line pilot tone detection.

This module is to be mounted in the VX-2000SF Surveillance Frame
and detects speaker line short circuits, open circuits by monitoring
for the presence of a pilot signal, and ground fault. Connecting the
supplied line to the end of the speaker line eliminates the necessity
of using the speaker line for line monitoring. However, the shielded
cable must be used for the speaker line.

Link to manufacturer information

VX-200SZ Audio Signal Output Module

The VX-200SZ is an audio signal output module of the VX-2000 system with speaker line impedance detection. This module is to be mounted in the VX-2000SF Surveillance Frame and detects speaker line short circuits, open circuits by comparing inpedance readings, and ground fault.

Link to manufacturer information

VX-200SZ-2 Dual Impedance Detection Module

The VX-200SZ-2 is an audio signal output module of the
VX-2000 system with speaker line impedance detection.

This module is to be mounted in the VX-2000SF Surveillance
Frame and detects speaker line short circuits, open circuits by
comparing impedance readings, and ground fault.
Since the mosule is equipped with 2 speaker outputs (A and B),
broadcasts can be maintained even if one of the two outputs fails.
Failures are indicated by the LED on the panel.

Link to manufacturer information

VX-200XI Audio Input Module

The VX-200XI module is designed to be used in conjunction with the VX-2000 System Manager, and comes with control input terminals, low-cut and high-cut filters, and gain controls.

Link to manufacturer information

VX-200XR Remote Microphone Input Module

The VX-200XR module is designed to be used with the RM-200X Remote microphone or RM-200XF Fireman's Microphone. Insert this module into the VX-2000's input module slot for each Remote or Fire Microphone(s) used in the system.

Link to manufacturer information

YA-1000A Fault Detection Circuit Module

The YA-1000A module is designed for use with VP Series power amplifiers and VM Series mixer power amplifiers. It detects breakages in the speaker-amplifier line loop by means of a 20kHz pilot signal. If there is any breakage, the amplifier POWER LED indicator goes out, activating the unit's relay output.

Link to manufacturer information

Related products:

The ZM-9001 is a remote control switch panel used with the M-9000. It adds 6 amplifier control inputs and can be mounted in an American Standard 1-gang electrical box in the wall.
Link to manufacturer information

Related products:

The ZM-9002 is a remote control switch/volume panel used with the M-9000. It adds 4 amplifier control inputs and 1 remote volume control, and can be mounted in an American Standard 1-gang electrical box in the wall.
Link to manufacturer information

Related products:

The ZP-001T is a zone paging module designed for use with the M-9000
and functions as interface to connect the M-9000 to an analog PABX,
allowing zone paging to be initiated from the PABX. There are two operation modes: ring signal and paging port modes. Broadcast can be initiated regardless of operation mode.
Link to manufacturer information

Related products: